Motion.conf - file

This is a copy/paste of the localhost:8080 file settings.

<– back

Camera 0
daemon = on
process_id_file = /var/run/motion/motion.pid
setup_mode = off
camera_name = (not defined)
logfile = /var/log/motion/motion.log
log_level = 6
log_type = all
videodevice = /dev/video0
v4l2_palette = 17
input = -1
norm = 0
frequency = 0
rotate = 0
width = 640
height = 480
framerate = 100
minimum_frame_time = 0
netcam_url = (not defined)
netcam_userpass = (not defined)
netcam_keepalive = on
netcam_proxy = (not defined)
netcam_tolerant_check = off
rtsp_uses_tcp = on
auto_brightness = on
brightness = 0
contrast = 0
saturation = 0
hue = 0
power_line_frequency = -1
roundrobin_frames = 1
roundrobin_skip = 1
switchfilter = off
threshold = 1500
threshold_tune = off
noise_level = 32
noise_tune = on
despeckle_filter = EedDl
area_detect = (not defined)
mask_file = (not defined)
smart_mask_speed = 0
lightswitch = 0
minimum_motion_frames = 1
pre_capture = 0
post_capture = 0
event_gap = 60
max_movie_time = 0
emulate_motion = off
output_pictures = off
output_debug_pictures = off
quality = 75
camera_id = 0
picture_type = jpeg
ffmpeg_output_movies = off
ffmpeg_output_debug_movies = off
ffmpeg_timelapse = 0
ffmpeg_timelapse_mode = daily
ffmpeg_bps = 400000
ffmpeg_variable_bitrate = 0
ffmpeg_video_codec = mpeg4
ffmpeg_duplicate_frames = off
use_extpipe = off
extpipe = (not defined)
snapshot_interval = 0
locate_motion_mode = off
locate_motion_style = box
text_right = %Y-%m-%d\n%T-%q
text_left = Camera 1
text_changes = off
text_event = %Y%m%d%H%M%S
text_double = on
exif_text = (not defined)
target_dir = /home/pi/motion
snapshot_filename = %v-%Y%m%d%H%M%S-snapshot
picture_filename = %v-%Y%m%d%H%M%S-%q
movie_filename = %v-%Y%m%d%H%M%S
timelapse_filename = %Y%m%d-timelapse
ipv6_enabled = off
stream_port = 8081
stream_quality = 100
stream_motion = on
stream_maxrate = 60
stream_localhost = off
stream_limit = 0
stream_auth_method = 0
stream_authentication = (not defined)
stream_preview_scale = 25
stream_preview_newline = off
webcontrol_port = 8080
webcontrol_localhost = off
webcontrol_html_output = on
webcontrol_authentication = (not defined)
track_type = 0
track_auto = off
track_port = (not defined)
track_motorx = 0
track_motorx_reverse = off
track_motory = 0
track_motory_reverse = off
track_maxx = 0
track_minx = 0
track_maxy = 0
track_miny = 0
track_homex = 128
track_homey = 128
track_iomojo_id = 0
track_step_angle_x = 10
track_step_angle_y = 10
track_move_wait = 10
track_speed = 255
track_stepsize = 40
quiet = on
on_event_start = (not defined)
on_event_end = (not defined)
on_picture_save = (not defined)
on_motion_detected = (not defined)
on_area_detected = (not defined)
on_movie_start = (not defined)
on_movie_end = (not defined)
on_camera_lost = (not defined)
sql_log_picture = on
sql_log_snapshot = on
sql_log_movie = off
sql_log_timelapse = off
sql_query = sql_query insert into security(camera, filename, frame, file_type, time_stamp, event_time_stamp) values('%t', '%f', '%q', '%n', '%Y-%m-%d %T', '%C')
database_type = (not defined)
database_dbname = (not defined)
database_host = localhost
database_user = (not defined)
database_password = (not defined)
database_port = 0
database_busy_timeout = 0
video_pipe = (not defined)
motion_video_pipe = (not defined)
camera = No threads
thread = No threads
camera_dir = /etc/conf.d
<– back

blogroll

social